Qshops Keurmerk Gezien op RTL4
491 beoordelingen
Uitstekende service en prima prijzen. Flexibel, snel en goede adviezen.Willem op 06-03-2019
Netjes van tevoren gebeld door een latere dag van leveren. Ook werd een wijziging van mijn bestelling op het laatste moment mog gped doorgevoerd. Top!Mark van de Kerkhof uit Helmond op 14-02-2019


IP Monitoring server en patch kasten, E-Mail, LAN, WiFi, PoE, SNMP

Artikelnummer: 140359
incl. BTW  362,12
excl. BTW € 299,27
1 tot 2 werkdagen
Dit product is met 1 tot 2 werkdagen te leveren.


Zeer uitgebreide en handige environmental / health monitoring systeem voor server rack en patchkasten. Uitgebreide functionaliteit en handige portal en mobile software. Verschillende aanvullende sensoren zijn leverbaar. Deze set wordt standaard geleverd met 1 x temperatuur sensor.


The new generation of IP thermometers: from now on up to three temperature or humidity sensors (even combi sensors) can be connected. Additionally also two dry digital inputs are integrated for processing of alarm contacts (door opening, smoke sensors, etc.). The device is made in a complete new mordern design compared to the last generation.

E-Mail: Today security is even more important for companies than ever before. Includes TLS transport encryption for e-mail transmission right from the start.

SMS: The device can control the SMS gateway directly over the network. Thanks to the decentralized architecture of the SMS gateway, several devices can also directly send SMS messages. This allows you to distribute a large mount of IP thermometers in your building, but send all SMS via one gateway.

Portal: If you would like to have access to your values from anywhere, the manufacturer‘s SensDesk portal is now available to you at any time. Including easy access via
web interface and directly via an app (Android, iOS) for your mobile phone. If you prefer to store your data internally, the software is also available.

Applications for the IP Thermometer:
•      EDV monitoring: Recording of relevant data in the server room and alerting the technicians.
•      Health sector: monitoring of refrigerators with medicinal products including reporting.
•      Food industry: monitoring the cold chain in many areas.
•      Heating systems: rapid notification after failure of critical systems.
•      Out of Band: Thanks to the integrated WiFi module it is also possible to connect difficult areas

Due to the changed hardware, the STE2 reacts much faster than its predecessor. In addition, a PoE functionality is now standardized in every device. Many customers do not always have a suitable network at the installation site of the IP thermometer. The STE2 provides here remedy by the built-in 2.4 Ghz WiFi module, which can work in the networks b / g / n


•      Network: RJ45 (10/100 MBit) incl. PoE power supply
•      WiFi: 2.4 Ghz 802.11 b/g/n
•      M2M protocols: SNMP (v1 and partially v2), XML, HWg-Push
•      Communication interfaces: E-Mail (TLS), SMS (via gateway)
•      Sensors: 2x RJ11 ports for temperature & humidity sensors
•      Digital inputs: 2 dry contact input


Interface :RJ45 (10/100BASE-T)

Supported protocol IP: ARP, TCP/IP (HTTP, SNTP, SMTP, HWg-Push, netGSM, TLS), UDP/IP (SNMP)

SNMP:Version 1 fully supported, some parts version 2


Supported standards: 802.11 b/g/n

Frequency: 2,4GHz


+19.5 dBm output power in 802.11b mode

+16 dBm for 802.11n

Security : WEP / WPA / WPA2 PSK / WPA2 TSK / WPS

Antenna : Internal

External sensors

Port / connector : Port1, Port2 / RJ11 (1-Wire)


Three external temperature or humidity sensors.

One combined temperature + humidity sensor can be connected.

Sensor type: Only sensors from HW group s.r.o.

Sensors / distance: Max 3 sensors / Max 60 metres total length

DI INPUTS (Dry Contact Inputs)

Port / connector : I1, I2 / ø 2 mm bracket

Type; Digital Input (supports NO/NC Dry contact)

Sensitivity: 1 (On) = 0-500 Ohm (Right pin on the terminal block can be connected to 12V GND)

Max. distance: Up to 50m

Power supply

Power voltage: 5V / 250 mA

Connector: Jack Ø3.5 x 1.35 / 10 [mm]


(Power over Ethernet): RJ45 - IEEE 802.3af Class 0



Green – Ethernet connection state


Yellow – Ethernet activity

Alarm: Port 1 – Alarm SENS – Shines if alarm active on sensor , Port 2 – Alarm DI – Shines if alarm active on sensor

IN: Yellow – activation of the contact

WiFi: Blue – connection state in operation (shining), search indicator (flashing slowly) and connection (flashing quickly)


Reset: Restore default settings: hold or 5 seconds after connecting power supply.

Other parameters

Operating temperature: -10 to 60 °C (range of device operating temperatures – may not correspond to  sensor range)

Dimensions/weight: 65 x 80 x 30 [mm] / 500 g

Elmag. Radiation: CE / FCC Part 15, Class B

Elmag. Compatibility: EN 55022, EN 55024, EN 61000